|
10-20-2017, 01:53 AM
|
#1
|
Member
Join Date: Sep 2016
Location: Calgary
Posts: 23
Alberta
|
A little windy
We got a call today from the owner of the campground where we have a permanent site. The night before half of the province was under a high wind warning of sustained winds of 130 KM/h (80 MPH).
We’ll apparently the wind pushed the front of our trailer about 3 feet sideways. Now I have to go out and assess the damage. From the picture the owner sent it looks like I need to replace at least 1 jack.
__________________
|
|
|
10-20-2017, 03:41 AM
|
#2
|
Senior Member
Join Date: May 2013
Location: Cody
Posts: 1,764
Wyoming
|
Sorry to see/hear about your damage...
That said, I just gotta make one comment... take it for what it’s worth:
I see yellow plastic leveling blocks in the photo, and I’m assuming they’re yours. If so, your rig is the THIRD I’ve personally witnessed this year of the gear sliding off of those square plastic blocks.
I have no idea what other’s experience with them has been, but I consider myself lucky that I was warned away from them early on in my RV life. I had a full set of them, all ready to use if ever needed, when a friend saw them in my basement and told me to give em to my grandkids to play with. His reasoning was that, while they fit together to each other well, they provide no friction-grip at all between the jack feet and the block. He said he’d seen many rigs’ landing gear slide right off of them if the terrain wasn’t level... and, high wind. To prove it, he had me hitch up... raise the landing gear... put a single block under each leg... and then lower the gear & unhitch. Then, he walked over... put his hands on the side on the rig... put his shoulder into it and PUSHED. Sure enough, the round feet of the landing gear had slid about an inch or more on the pad!
Since then, I only carry wood blocks. Went to Lowes, had then rip a 10-foot long pressure treated 2x10 into twelve 10”x10” squares that I keep in the truck box.
__________________
__________________
Tom
2013 VOLTAGE 3200 (EPIC I & II)
2014 Ford F-450 PLATINUM
2018 BMW R1200GS RALLYE
|
|
|
10-20-2017, 10:17 AM
|
#3
|
Senior Member
Join Date: Jan 2015
Location: Roselle
Posts: 1,292
Illinois
|
Good tip Tom, thanks. Never thought about it.
Rusty
__________________
2015 Black F-350 Platinum Diesel Dually Crew Cab
2019 Riverstone Legacy 38MB (Full Paint/All Options)
2015 Voltage 3990 (Full Paint, All Options) Sold 6/18
2005 Harley Ultra Classic w/too many miles
|
|
|
10-20-2017, 04:22 PM
|
#4
|
Senior Member
Join Date: Dec 2012
Location: Tahlequah
Posts: 3,079
Oklahoma
|
Something to add to your vast intelligence base, Lowe's doesn't 'rip' wood, the machine doesn't allow length wise cutting. They can however, 'cross cut' many wood and wood based products.
__________________
2013 Voltage 3800, 2012 Chevy 3500 HD
2010 Yamaha V Star 950
2009 Yamaha Raider
Volunteering with Habitat for Humanity Caravanners
|
|
|
10-20-2017, 05:02 PM
|
#5
|
Senior Member
Join Date: May 2013
Location: Cody
Posts: 1,764
Wyoming
|
Quote:
Originally Posted by sundancer 87
Something to add to your vast intelligence base, Lowe's doesn't 'rip' wood, the machine doesn't allow length wise cutting. They can however, 'cross cut' many wood and wood based products.
|
Ha! Yeah, yeah... ok, you got me.
__________________
Tom
2013 VOLTAGE 3200 (EPIC I & II)
2014 Ford F-450 PLATINUM
2018 BMW R1200GS RALLYE
|
|
|
10-20-2017, 05:04 PM
|
#6
|
Member
Join Date: Aug 2016
Location: Elk Grove, CA/Seal Rock, OR
Posts: 24
California
|
I have the same plastic blocks for my stabilizers since I have limited storage for wood. I solved any sliding problem by applying some left over Rhinoliner with coarse sand embedded on just four of them. Those 4 always go on top if I need to stack a couple, the jack pads will not move at all. I use tiered 2x6's for leveling the tires and tongue jack.
|
|
|
10-20-2017, 05:54 PM
|
#7
|
Senior Member
Join Date: Dec 2012
Location: Tahlequah
Posts: 3,079
Oklahoma
|
Quote:
Originally Posted by ATCguy
Ha! Yeah, yeah... ok, you got me.
|
debil made me do it
__________________
2013 Voltage 3800, 2012 Chevy 3500 HD
2010 Yamaha V Star 950
2009 Yamaha Raider
Volunteering with Habitat for Humanity Caravanners
|
|
|
10-21-2017, 02:19 PM
|
#8
|
Senior Member
Join Date: May 2013
Location: Cody
Posts: 1,764
Wyoming
|
Quote:
Originally Posted by Kuhl951
I have the same plastic blocks for my stabilizers since I have limited storage for wood. I solved any sliding problem by applying some left over Rhinoliner with coarse sand embedded on just four of them. Those 4 always go on top if I need to stack a couple, the jack pads will not move at all. I use tiered 2x6's for leveling the tires and tongue jack.
|
Hey, great! Whatever it takes... I’m just saying that, as sold, they seem to be weak.
The most recent that I saw was over Labor Day... I was at the West Yellowstone KOA, and all of the campsites are on a slope of a mountainside. The sites themselves are somewhat terraced, but they’re still not level. I had to use blocks for the left side, my wheels were 4-6 inches off the ground... and so were most others around me.
One morning I was sitting on the back patio checking email when I heard BOOM! from the rig next door. At first I had no idea what had happened, but went outside to go check that everything was ok. As I was on my way over, the owner came outside and walked to the front of the rig. From there it was easy to see what had happened. The entire front of the rig had shifted left (downhill), as the landing gear had slipped off of his orange plastic blocks. The left leg was bent slightly from the impact, but the right side was bent completely under.
They used the campground back-hoe & some railroad ties to lift the rig, and block it enough so he could back his truck up & rehitch to tow it away for repair. But it was just out of the blue... no strong wind or anything. He had the wheels chocked, nothing out of the ordinary. But his normal moving about in the rig was enough for those landing gear feet to simply slide right off the blocks.
__________________
Tom
2013 VOLTAGE 3200 (EPIC I & II)
2014 Ford F-450 PLATINUM
2018 BMW R1200GS RALLYE
|
|
|
10-21-2017, 03:01 PM
|
#9
|
Senior Member
Join Date: May 2016
Location: Alvin
Posts: 727
Texas
|
Great post. I could see the movie in my head while I read the words. And although none of my rigs are very big or heavy, I get the feeling it applies even more! I'm convinced. And I will consider it yet another "best practice" that I was gifted by this amazing forum.
Thanks everybody!
__________________
2017 Aerolite 213 RBSL-ND
2018 Wolf Pup 17RP Limited (Tiny THauler)
2018 F150 King Ranch 3.5 Beast
2003 Ram 2500 Cummins (can't kill this beast)
|
|
|
10-21-2017, 03:14 PM
|
#10
|
Member
Join Date: Sep 2016
Location: Calgary
Posts: 23
Alberta
|
Yeah I’ll have to rethink the block for the tongue jack. I agree that it could have definitely slipped off the plastic block. Still though. It got pushed another 2 1/2’ with out the block
|
|
|
10-21-2017, 04:38 PM
|
#11
|
Senior Member
Join Date: Dec 2012
Location: Tahlequah
Posts: 3,079
Oklahoma
|
This reminds me of when I lived on a beach in Mexico. I had lived in a rehabbed 27 foot TT while building my house.
I looked out one morning after a somewhat normal breezy night to find my TT had been storm surged 30 feet from where is was prior to the surge.
Filled with sand and sea water, dripping from the humidity I declared it a total loss. I pulled the refrigerator and converter and batteries. There were a few fishermen there by that time so I told them to haul it away.
Not as bad as having a current use TT being jacked around by the wind but a box will blow away with enough wind.
__________________
2013 Voltage 3800, 2012 Chevy 3500 HD
2010 Yamaha V Star 950
2009 Yamaha Raider
Volunteering with Habitat for Humanity Caravanners
|
|
|
10-24-2017, 02:58 AM
|
#12
|
Member
Join Date: Sep 2016
Location: Calgary
Posts: 23
Alberta
|
Here are a couple of more pics from my trip out there this past weekend. The wind buried the pin in the ground about 3 inches. There is a flat plate on the bottom of it.
__________________
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|